Setup Guide

Netbell SIP Speakers with RingCentral

Register a Netbell SIP speaker or paging gateway as a RingCentral paging device, then page it from any RingCentral phone by dialing *84 and the group extension.

Updated October 30, 2026 5 min read Download PDF
Before You Start

01Before You Start

This guide applies to the Netbell SIP AU-711-SIP paging gateway and the WM-042S, CM-600S and H30-709S speakers. It also works with RingCentral plans resold by AT&T (AT&T Office@Hand).

It takes four steps:

  1. Add the speaker as a paging device in RingCentral.
  2. Set up the speaker with the RingCentral account details.
  3. Create a paging group in RingCentral.
  4. Page the speaker from a RingCentral phone.

You need a RingCentral administrator login, and a Windows PC on the same network as the speaker.

02Step 1: Add a Paging Device in RingCentral

  1. Log in to the RingCentral Admin Portal at service.ringcentral.com with your admin login.
  2. Go to Phone & Devices › Manage Devices › Phones & Devices › Paging Devices.
  3. Click Add Device and enter a Nickname, for example Warehouse Speaker.
  4. On Provisioning Info, at Step 1 (“Will you be using secure voice transport on this device?”), select No. The Netbell registers over standard UDP.
  5. In Outbound Proxy, choose the proxy for your region, for example sip12.ringcentral.com:5090 for North America, and click Done.
  6. Double-click the new device in the list to open its Paging Device Info. Keep this page open: you copy its values into the speaker in Step 2.
Figure 1Provisioning info for the paging device

03Step 2: Set Up the Speaker

Connect the Speaker

Connect the speaker to a PoE network switch with a CAT5/5e/6 cable. Without PoE, use a 12/24 VDC power adapter (not supplied).

Warning

Don’t use PoE and a power adapter at the same time.

When the green LED blinks and the blue LED stays on, the speaker is ready.

Find It with the SIP Config Tool

  1. Download and install the SIP Config Tool from Support Programming. The PC must be on the same network as the speaker.
  2. Click Search Devices. Check that the speaker’s IP address fits your network. The default is 192.168.1.xxx.
  3. If it doesn’t, select the speaker, enter the right IP Address, Subnet Mask and Gateway, and click Save. Wait about 10 seconds and click Search Devices again.
  4. Double-click the speaker to open its login page in your browser.
Figure 2The SIP Config Tool after Search Devices

Log In and Check the Network

  1. Log in with user name admin and password 123456.
  2. On the Network page, check that the Primary and Secondary DNS are right for your network, and save if you change them. The speaker needs DNS to find the RingCentral servers.
Tip

Change the default password on the speaker’s Security page. See the Netbell-SIP Speaker User Manual.

Enter the RingCentral Account

Open Sip Setting and copy the values from the RingCentral Paging Device Info page:

In RingCentral On the speaker
User Name User account
Password Password: type it in, don’t paste it
SIP Domain, e.g. sip.ringcentral.com:5060 Server address: sip.ringcentral.com
Server Port: 5060
Outbound Proxy, e.g. sip12.ringcentral.com:5090 Outbound Proxy: sip12.ringcentral.com
Proxy port: 5090
Authorization ID Authentication Username
Device nickname Display Name (any name)

Enter the address and port in separate fields: the part before the colon is the address, the number after it is the port. Use the Primary Server column.

Important

Type the password by hand. Copy and paste can add hidden characters, and then the speaker won’t register.

Click Save, then Logout and log in again to apply the settings.

Figure 3RingCentral details on the Netbell’s Sip Setting page

Check That It’s Registered

  • On the speaker’s Overview page, Server Status shows Connected and the RingCentral server address.
  • In RingCentral, refresh the Paging Device Info page: the device shows Online.

If not, check the account details and the DNS settings again.

Set Auto Answer and Codecs

Open Work Setting › Intercom and set:

Setting Enter
Auto Answer 0, so pages play at once without ringing
Codec priority Turn on all three, in this order: G.722 (best quality, if supported), G.711u (most compatible; recommended in the U.S.), G.711a
Talk Volume Loud enough to be heard clearly in the area

04Step 3: Create a Paging Group in RingCentral

  1. When the speaker shows Online, go to Groups › Paging Only and click New Paging Only.
  2. Enter a Group Name and an Extension number, and save.
  3. Click the group, open Paging Only Details, and make sure the group is Enabled.
  4. Open Paging › Devices that receive pages for this group and add the Netbell speaker.
  5. Open Members allowed to page this group, click Add member, choose the users who may page (or all), and click Add.
Figure 4A paging group with extension 1009
Figure 5Devices and members of the paging group

05Step 4: Page the Speaker

From a RingCentral phone of a member allowed to page, dial *84 followed by the group’s extension. For example, for extension 1009:

*841009

Speak after the tone. Your voice plays on every speaker in the group.

06Troubleshooting

  • Server Status isn’t Connected: retype the password by hand; check the User account, Authentication Username, and that address and port are in separate fields; check the DNS servers on the Network page.
  • The device shows Online but pages don’t play: check that the speaker is added under Devices that receive pages, the group is Enabled, and Auto Answer is 0.
  • Paging doesn’t work from one phone: add that user under Members allowed to page this group.
  • Choppy or no audio: check the codec order, and that your firewall allows the speaker to reach RingCentral.

For more settings, such as forwarding audio to other speakers, see the Netbell-SIP Speaker User Manual. Still stuck? Contact Linortek tech support or call 336-485-6199.

Still stuck? Our support team can help with setup and configuration.

support@linortek.com