User Manual

Netbell-NTG PA System Controller

Wiring, 70 V speakers, audio tones, bell schedules, external triggers and custom sounds for the Netbell-NTG.

Updated August 17, 2026 21 min read Download PDF
Wiring the Netbell-NTG

01Wiring the Netbell-NTG

The Netbell-NTG is a self-contained web server with input and output circuits designed to send an audio signal to a PA system.

Warning

Do not use voltages above 48 V through the Netbell-NTG. It is not safe.

Audio Output Ratings

The Netbell-NTG line output is rated at 30 Ω impedance, 70 mA maximum, 2.1 V audio signal. It can be wired directly to a power amplifier that uses AC voltage. Note the impedance of your speakers and how they are wired, and use this calculation to check you are within the amplifier’s impedance rating, where R is each speaker’s impedance in ohms:

Rtotal = 1 ÷ (1/R1 + 1/R2 + …)

The stereo line out is a terminal block with left and right outputs. Connect it to a power amplifier for higher volume or to drive larger speakers. Make sure the amplifier has a stereo line input and is rated to drive the speakers you want to connect.

Note

Linortek is not responsible for third-party amplifiers or speakers connected to the device, or for failure of the Netbell-NTG when wired incorrectly.

Two cables are supplied for connecting to an amplifier or PA system: RCA stereo to line out and 3.5 mm stereo to line out. Choose the one that matches your amplifier’s audio input; see Audio Output Connection.

Figure 1Supplied audio cables

Ethernet Connection

Plug an Ethernet cable into the NET connector. The device is PoE-enabled.

Important

The Netbell-NTG only works with IEEE 802.3af or 802.3at PoE. Check your network switch specifications before plugging the device in, to prevent damage.

On a PoE switch with a 100 Mbps network available, the green Boot LED on the device and the Connection LED on the Ethernet connector come on; otherwise they stay off. The Activity LED blinks to show network activity. If the device is powered by PoE, do not also connect the 12 VDC power supply.

Power Connection

  1. Connect the positive wire of the 12 VDC power supply to the 12VDC terminal, and the negative wire (marked with a white stripe) to the GND terminal.
  2. Plug the power supply into a suitable AC outlet.
LED Meaning
Green (Boot) flashing The Netbell-NTG is running in Bootloader mode, right after power-on.
Red blinking After about 5 seconds the green LED goes off and the red LED blinks: the device is in Server mode and reachable on the network over TCP/IP.

Connecting Several Netbell-NTGs to One Amplifier

Warning

Do not connect multiple Netbell-NTG audio outputs directly in parallel to a single amplifier input. Netbell-NTG units use active line-level outputs; paralleling them without isolation makes the devices drive into each other. This can damage equipment and is not covered under warranty.

Approved methods Prohibited wiring
Line-level audio mixer (recommended) Direct parallel connections
Proper resistor summing network (unbalanced audio) Y-cables or splitters
Audio relay or source selector (single source active) Twisting or tying signal wires together

Audio Output Connection

Choose the connection that matches the input on your amplifier:

Amplifier input How to connect
RCA (most common) The RCA cable comes pre-wired to the Netbell-NTG Line Out terminal block. Plug it straight into the amplifier.
3.5 mm stereo jack Use the supplied 3.5 mm stereo to line out cable. Wire white to LFT, red to RGT, and the black wires to GND.
Audio line input (terminals) Use two 18 AWG 2-ply cables (not supplied). Both sides use the same colors, so wire the left side completely before the right to avoid crossing them. Use black for GND and red for LFT / RGT.

Relay Output Connection

The board has two dry-contact relay outputs (48 V max; 5 A @ 12 VDC, 3 A @ 24 VDC). Each relay has three terminals: NO (Normally Open), C (Common) and NC (Normally Closed). Connect physical bells or buzzers to C and NO:

  1. Select a power source that meets the requirements of the bell or buzzer.
  2. Wire one side of the power source to one side of the bell, and the other power wire to relay terminal C.
  3. Connect the other side of the bell to relay terminal NO.

Digital Input Connection

The board has 4 digital inputs (5–24 VDC) for triggering special notifications or emergency alerts. A sensor such as a temperature sensor or a push switch can be connected to a digital input.

Important

When connecting a 12–48 VDC sensor to an input, you must use an external resistor (2.2 kΩ, 0.5 W; provided on request).

The inputs have two modes, selected by the switch on the board marked ISO (isolated) and PU (pull-up). Put the switch up for pull-up and down for isolated.

Mode How it works
ISOLATED You drive the opto-isolator directly with an external voltage through an internal 1 kΩ resistor. The voltage can be 5–48 VDC, supplying a minimum of 2 mA and a maximum of 30 mA to the opto-isolator diode. There is no other internal connection to this voltage, so the input is isolated.
PULL UP Connects a 1 kΩ resistor to an internal voltage, so you can use a simple switch (such as a magnetic door switch) across terminals 1 and 2. When the switch is activated, a signal is sent to the input.
Caution

These units are ground-isolated. Connect so the power loop is connected only to the Netbell-NTG, and do not use external ground connections. If you use isolated mode, set the input switch before applying an external voltage. Doing otherwise may damage the Netbell-NTG or the PoE source device.

Wiring a push button

For distances up to 500 ft, 20 AWG shielded wire is suitable. For distances up to 5,000 ft, use 16 AWG shielded cable instead. Longer cable runs are more susceptible to signal interference.

Background Music Connection

Figure 2Background music wiring

The Netbell-NTG can use its relays to switch an external stereo source, such as a PA system or music player, off while it plays a tone. As shown above, the external source is wired through the relays on a Normally Closed circuit and then to the Netbell-NTG’s audio Line Out.

You then configure the Netbell-NTG to disconnect the music while the tone plays; see Interrupting Background Music.

02Speaker System

Figure 3Netbell-NTG speaker system wiring diagram

Speaker Connection

Speaker 70 V / positive COM / negative
30 W speaker White Green/black
20 W speaker White Black

This is a 70 V speaker system. 70 V speakers are wired in parallel, and their combined wattage should be no more than 80% of the amplifier’s output to leave headroom. Connect each speaker’s 70 V wire to the amplifier’s 70 V output and its COM wire to the amplifier’s ground/negative (COM/−). The diagram shows 3 speakers; add more to the 70 V circuit exactly like speaker #3. For details, see the manual that came with your amplifier.

Figure 4Wiring 3 speakers in parallel

Cable Requirements

If you need to extend the cable, it usually does not need to be shielded, but it should be heavy enough to minimize losses from wire resistance over long runs (insertion loss). Cable thinner than 18 AWG is not recommended; long runs need 16 AWG or heavier.

Shielded output cable may be needed where the cable runs close to unshielded intercom cables, electrical cables, radio antennas or other sources of interference, or when the amplifier is used for paging from a telephone system, to prevent feedback or interference.

Maximum Wire Length

Use high-quality, heavy-gauge, two-conductor twisted speaker cable; 14–16 AWG works in most applications. The maximum length of a 70 V line depends on the wire gauge:

Speaker cable transmission distance as a function of conductor size vs. power loss in the cable (% loss and dB loss). Distances in feet.
AWG 4 Ω speaker 8 Ω speaker 70 V speaker
11%
0.5 dB
21%
1 dB
50%
3 dB
11%
0.5 dB
21%
1 dB
50%
3 dB
11%
0.5 dB
21%
1 dB
50%
3 dB
6 277 571 1,930 554 1,141 3,859 13,580 27,965 94,548
8 174 359 1,214 349 718 2,428 8,546 17,598 59,498
10 110 226 764 219 452 1,528 5,377 11,072 37,434
12 69 142 480 138 284 959 3,376 6,952 23,505
14 43 89 302 87 179 604 2,127 4,380 14,809
16 27 55 185 53 110 371 1,305 2,687 9,085
18 17 35 117 34 69 234 823 1,694 5,726
20 11 22 74 21 44 147 518 1,068 3,610
22 7 13 46 13 27 91 321 661 2,234
24 4 9 29 8 17 57 202 417 1,409

Speaker Placement

Speaker type Where and how to place it
Ceiling speakers Used with drop-tile ceilings, for heights of 8–20 ft. Rule of thumb: space them at twice the ceiling height; for an 8 ft ceiling, place speakers 16 ft apart.
Wall baffles Send sound horizontally rather than down. Normally spaced 20 ft apart and never directly facing each other. A good option for offices or schools with ceilings over 20 ft that aren’t large enough for horns.
Horns Used in manufacturing, warehouse and outdoor areas. Mount 15–20+ ft off the ground, 50–100+ ft apart, aimed 30° down from horizontal (60° up from straight down). Never directly facing each other.

To lay out the speakers, start in one corner of the area. Place the first speaker in Row 1 at a distance of ½ C, then each following speaker in the row at a distance of C. Start Row 2 at distance D from Row 1. Continue in the same alternating pattern until the whole area is covered.

Figure 5Speaker layout sample
Ambient noise range Speaker power tap (W) C D
Medium noise (65–75 dB) 20 110 70
High noise (75–85 dB) 20 100 65
Very high noise (85–95 dB) 20 65 40
High noise (75–85 dB) 30 100 65
Very high noise (85–95 dB) 30 95 58

Installing the 30 W Horn Speaker

  1. The 30 W speaker has a pivoting cast-iron base with 3 screw holes. Using screws with heads larger than ¼ in diameter, screw the base to the mounting surface.
  2. Two screws are attached to the horn for mounting. Choose one and remove it from the horn.
  3. Slide the screw through the hole in the top of the base and tighten it.
  4. Adjust the angle: the screw on the base gives horizontal movement and the wingnut near the mounting surface gives vertical movement. Loosen either one, set the angle, then tighten.
  5. On the rear of the horn is a selectable 70/25 V transformer. Using the chart printed above the transformer screw, turn the screw to the power and voltage setting you want.
  6. The wire connections are sealed inside for weatherproofing and are reached through a 2 ft lead. Connect the white (positive) and black (negative) wires to the matching outputs on your amplifier.
  7. Connect the green/yellow ground wire to the building structure or a grounding device.
Caution

Make sure the power you select, combined with all other speakers, does not exceed 80% of your amplifier’s rated power. Contact Linortek Technical Support if you are unsure.

03Finding the IP Address

By default the Netbell-NTG uses DHCP: when first installed, it gets an IP address from your router if the router is set up to assign one. If not, use Option 3 to connect with the default IP address and set a static one.

Option 1: Linortek Discover

Two Discover apps are available from Support Programming:

  • Linortek Discover for Windows PCs and Android phones (recommended on Windows).
  • Linortek TCP/IP Discoverer, a Java app for any computer with the Java Runtime installed.

Linortek Discover for Windows

  1. Download the .zip file and extract it.
  2. Double-click Linortek_Discover_Windows.exe.
  3. If Windows shows “Windows protected your PC… Microsoft Defender SmartScreen prevented an unrecognized app from starting”, click More info, then Run anyway. The app will not harm your computer.
Figure 6Running Linortek Discover on Windows

Linortek Java-based TCP/IP Discoverer

Depending on your browser’s security settings, you may see a warning asking whether to keep or discard the download. Click Keep; it is a Java program and will not harm your computer.

What Discover shows

  • Port number (Windows app only; 30303 by default, used by most Linortek products)
  • IP address
  • Host name
  • MAC address
  • Other info: blue LED (if on), product name, server software revision
Figure 7Linortek Discover for Windows
Figure 8Java TCP/IP Discoverer

Click your device in Discover to open its web pages in your browser, then click Login on the home page. The default username/password is admin/admin. You can change these, or disable login, in the Settings menu.

Option 2: Ping the Device

If Discover doesn’t work, ping the device to get its IP address:

  1. Open the Start menu, type cmd and select Command Prompt.
  2. Type the following and press Enter:
    ping server
  3. If the ping succeeds, you will see replies from the device’s IP address. Type that address into your browser.

Option 3: Connect Directly to Your PC

If you still can’t find the IP address, or your network doesn’t support DHCP, connect the Netbell-NTG directly to your computer’s Ethernet port, turn off Wi-Fi, and enter the default IP address 169.254.1.1 in your browser.

Once logged in, set a static IP address on the Configure › Network Config page. You can then connect the device to your network and reach it at that static address.

04Basic Software Configuration

If you are configuring your Netbell-NTG for the first time, start by enabling the audio system. If you have already done this, skip to Assigning Audio Tones to Relays.

Enabling the Audio File System

  1. Open the SETTINGS drop-down menu and click SETTINGS.
  2. Enter audio in the UART Usage field (not case-sensitive).
  3. Check Use Audio File System.
  4. Click SAVE. The device starts playing through the files on the SD card.
Figure 9Enabling the audio file system

Setting Time and Date

When you first configure your Netbell-NTG, check the time and date on the home page. The device is set by default to Eastern Standard Time (GMT-5) with Daylight Saving Time correction. To change this, open Settings › Time/Date and change the value in the third box, Time Zone.

If you intend to keep the Netbell-NTG off the network after configuring it, uncheck Use Daylight Savings Time and Use NTP Update. You then need to adjust the time manually for daylight saving and periodically to correct clock drift.

To use your own internal NTP server, see How to Use Your Internal NTP Server for Linortek Devices.

Caution

Incorrect NTP settings can stop your devices from updating their time.

Figure 10Settings › Time/Date

05Assigning Audio Tones to Relays

On the Netbell-NTG, a relay is used only to trigger a tone; it does not act as a physical switch here. You can assign a tone to any relay (1–8) and schedule it on the Services › Bells page.

Enabling the Extended Relay Range (Relays 5–8)

The Netbell-NTG has 2 physical relays, but you can activate up to 8 relays in software for scheduling extra tones and messages. Only 4 relays are visible by default.

  1. Open Settings › Settings.
  2. Check Extend Relay Range and click SAVE.
  3. Go to Services › Relays, and in the browser’s address bar change relays4 to relays8. For example, http://172.16.10.105/p/relays4.htm becomes http://172.16.10.105/p/relays8.htm.

You can now assign tones to relays 5–8 on the Tasks page. They correspond to Bells 5–8 on the bell schedule page.

Audio Files

The device comes with 40 factory sounds, listed in the Netbell Standard Sound List. You can add your own sounds or recorded messages to the SD card (up to 10 hours in total) in .ogg format; the Netbell-NTG only plays .ogg files. To convert other formats, see Creating Custom Sounds.

Assigning a Tone to a Relay

This example assigns the tone BELLT001 to relay 1.

  1. Open the Tasks page and click the Edit icon at the end of the first available line.
  2. Enter a name in Schedule Name if you like, and check Use.
  3. Set Device A to RELAY and Data A to 01+. This means Bell 1 on the bell schedule page; for bells 2, 3 … use 02+, 03+ ….
  4. Set Device C to SEND UART and Data C to PBELLT001OGG: the 8-character file name, preceded by P and followed by OGG, all in capitals.
  5. Set Action to ON and click SAVE.
Figure 11Task assigning tone BELLT001 to Bell 1

UART Audio Commands: Loop, Stop and File Mode

As well as playing a file with P<FILENAME>OGG, you can enter these commands in Data C of a SEND UART action, manually or through the schedule. Use them in separate tasks or combined with scheduled events.

Data C What it does
c Continuous play: loops all audio files stored on the SD card.
C Stops playback based on a condition, for example stopping a 1-minute file when Relay 1 turns off.
f File mode: returns to normal file playback (exits continuous play started with c).
Figure 12Using c to start the loop when Relay 1 is on, and f to return to file mode when Relay 1 is off
Figure 13Using C to stop playback when Relay 1 is off

06Scheduling Audio Playback

Once the audio system is enabled and a tone is assigned to a relay, you can schedule playback with the built-in bell scheduler, or trigger it from an external signal.

Creating a Schedule on the Bells Page

Each Netbell-NTG can hold up to 500 bell events. Open the Services drop-down menu and select Bells.

Figure 14Services › Bells
  1. Enter an event Name of up to 15 characters, using letters and numbers only.
  2. Use the three Time fields to enter the time as HH:MM:SS. The hour field uses 24-hour format: select 00 for 12 AM and 13 for 1 PM.
  3. Enter a Duration and select its unit (mS, Sec, Min). Don’t leave this empty, or the schedule may not work. Playback length is set by the audio file: a 10-second file plays for 10 seconds whatever duration you enter.
  4. Optional: enter a Date. The event then triggers only on that date.
  5. Click Add. The event appears in the list above, in chronological order.
  6. Choose which relays the event triggers with pips 1–8 in the Bell column. 1 and 2 are selected by default. Note which numbers you use, as you assign a sound to each. For 5–8, see Enabling the Extended Relay Range.
  7. Choose the days of the week in the Day column (Sunday – Saturday). A specific date overrides the Day column.
  8. Check Use to enable the event. To trigger it only once, also check Once.
Figure 15Example bell schedule

Deleting Items

To delete one event, click DEL to the right of it. To clear the entire schedule, enter #!reset@memory! in the Name field and click Add.

Warning

This removes every event in the schedule. Save a copy first.

Uploading a Premade Schedule

  1. Enter #upload in the Name field and click Add. A new page opens.
  2. Click Choose File and select your schedule in .txt or .csv format.
  3. Click Upload. You return to the Bells page with your new schedule listed.

You can write a schedule in a plain text editor such as Notepad. The first line must be #Start; each following line is one event with 13 comma-separated items. Save the file as plain text (.txt).

Figure 16Sample prewritten bell schedule

Saving Your Bell Schedule

Click Download at the bottom right of the Bells page. A new browser tab opens showing the schedule as plain text. Copy it into a plain text editor such as Notepad and save it.

07Using an External Trigger

You can program the Netbell-NTG to play a tone from an external trigger such as a push button or a door contact switch.

Note

Unless your trigger device supplies its own power, set the input switch to Pull Up (PU). See Digital Input Connection and Board Layout Reference. The steps below assume digital input 1 and the tone EVACUATE.

Activating the Digital Input

Open the Services drop-down menu and select Inputs. The top 4 items, DIN 1 – DIN 4, are your digital inputs. Click the blue pencil icon under DIN 1 and enter:

  1. Name and Label – optional.
  2. Check Use.
  3. Set Type to State and Display to Dot.
  4. Set Relay L/T to 0.
  5. Set Command L/Z/N/I to Inv.
  6. Click SAVE.
Figure 17Digital input settings

Setting a Task for the Digital Input

  1. Open the Tasks page and click the Edit icon on the first available task.
  2. Name the task if you like, and check Use.
  3. Set Device A to Digital and Data A to 1S=1. Here 1 is the input number, S means the input state, and the final 1 means the state is on.
  4. Set Device C to Send UART and Data C to PEVACUATEOGG (plays the file EVACUATE).
  5. Set Action to ON and click SAVE.

For a door contact switch, set Data A to 1S=0 to play the tone when the contact is broken.

Figure 18Task for digital input 1

08Interrupting Background Music

The Netbell-NTG can interrupt background music from an external source. Once it is wired to your audio system as shown in Background Music Connection, you can program it to open its relays, play a prerecorded tone or message, and then reconnect the music.

  1. Create a bell schedule event for the times you want. Trigger relays (bells) 1 and 2 to disconnect the external source, and use a relay from 3–8 to play the audio file.
  2. Create a task for that relay (3–8) to trigger the tone or message, as described in Assigning a Tone to a Relay.

09Creating Custom Sounds

Besides the 40 factory sounds, you can create custom sounds or record messages and save them to the built-in micro SD card. The Netbell-NTG plays .ogg files, so other formats must be converted. We recommend Audacity, a free program that records directly to .ogg and converts other audio files.

Important

File names must be exactly 8 characters, using only capital letters and numbers, for example SOUND001. Otherwise the audio file system will not recognize the file.

Adding Custom Sounds or Messages

  1. Choose your sounds, or record a message on your computer or phone.
  2. Open the lid of the Netbell-NTG and remove the micro SD card from its slot.
  3. Insert the card into your computer’s micro SD slot, or connect it with a card reader.
  4. Convert your audio files to .ogg with Audacity (any converter works, but Audacity is the simplest way to record, edit and convert).
  5. Export the file to the micro SD card with an 8-character name.
  6. Put the micro SD card back into the Netbell-NTG’s card slot.
  7. Set up your new sounds as described in Assigning Audio Tones to Relays and Scheduling Audio Playback.

Using Audacity

  1. Download Audacity and install it.
  2. Open your audio file with File › Open.
  3. Export it with File › Export › Export as OGG, saving it to the SD card.
Figure 19Exporting as OGG in Audacity
Tip

To change the pitch, select the whole file with Ctrl + A, then choose Effect › Change Pitch.

10Board Layout Reference

Figure 20Netbell-NTG board
  1. Micro SD card slot
  2. Audio module
  3. Digital input switches (4, 3, 2, 1 from left to right)
  4. RJ45 connector
  5. Reset button
  6. Reload button (turns on the blue LED, which identifies the unit in Discover)
  • The device ships with a 1 GB micro SD card, enough for over 10 hours of audio. A larger card can easily be fitted.
  • The line out is split into left and right for stereo sound, for use with an amplifier. It has a 30 Ω impedance rating.
  • A 12 VDC power supply is included. The device is also PoE-enabled (IEEE 802.3af or 802.3at only; check your switch before connecting).

Factory Reset

Using the buttons

  1. Press the RESET button. The red LED blinks and the green LED is on (Bootload state).
  2. While in this state, press and hold the RELOAD (DFLT) button for about 10–15 seconds, until the red LED comes on steady (blinking at a 1-second rate).

Using the web interface

  1. Open System › Load/Reboot System.
  2. Check Restore Default Values and click Boot Mode.
  3. The device is reset to factory defaults once the red LED returns to normal (blinking at a 1-second rate).

More Help

Still stuck? Our support team can help with setup and configuration.

support@linortek.com